The ANSUL R-102 is the most widely used kitchen fire suppression system in commercial kitchens. This guide explains, in plain language, how the system works, what its main parts do, how it is sized, and what maintenance it needs to stay ready. The information is based on the manufacturer’s R-102 Design, Installation, Recharge and Maintenance Manual (Part No. 418087). It is written by the AMH-CO team, who have supplied, installed and maintained ANSUL R-102 systems in Saudi Arabia since 2007.
What the R-102 system protects
The R-102 is a pre-engineered system that protects three areas of a commercial kitchen at the same time: the cooking appliances (fryers, ranges, griddles, char-broilers, woks, upright and chain broilers), the plenum (the space behind the hood filters) and the exhaust duct. It is listed by Underwriters Laboratories to the UL 300 test standard, which requires fires in grease-loaded appliances, plenums and ducts to be put out after they reach full intensity. Design and maintenance follow NFPA 17A (wet chemical systems) and NFPA 96 (commercial kitchen ventilation).
How the system works
- Detection: fusible links hang in the hood and duct on a stainless steel wire rope. When the temperature at a link reaches its rating, the link separates and releases the wire rope.
- Release: the AUTOMAN regulated release mechanism punctures a gas cartridge (nitrogen or carbon dioxide). A regulator feeds the gas into the agent tank at a constant 110 psi (7.6 bar).
- Discharge: the pressure pushes ANSULEX Low pH liquid agent through the piping and out of the nozzles over the appliances, the plenum and the duct.
- Extinguishing: the agent cools the hot oil and reacts with it (saponification) to form a soap-like foam layer that seals the surface and helps prevent re-ignition.
- Shut-off: the release closes the gas valve to the appliances and, through electrical switches, can shut down electric appliances and trigger alarms.
The system can also be operated by hand from the red remote manual pull station, which should be mounted on the exit path from the kitchen.
What happens to the exhaust fan? The manufacturer advises leaving the exhaust fans running: the airflow helps carry the agent through the duct and cools the plenum and duct after discharge (the system is listed with or without fan operation). Make-up or supply air fans built into the protected hood must shut down when the system operates. See our upblast fan guide for choosing the exhaust fan.
Main components
| Component | What it does |
|---|---|
| AUTOMAN regulated release (429853) | The heart of the system: holds the release mechanism, regulator and the first agent tank. |
| 1.5 gallon tank (429864) / 3.0 gallon tank (429862) | Stainless steel tanks that store the liquid agent. Each tank has a burst disc that prevents siphoning when temperatures change. |
| ANSULEX Low pH 1.5 gallon (79694) / 3.0 gallon (79372) | Potassium-based wet chemical agent. One container fills one tank. Storage life is twelve years. |
| Gas cartridges (double tank, LT-A-101-30 and others) | Nitrogen or carbon dioxide cartridges that pressurise the tank(s) when the system operates. The cartridge size depends on the number of tanks. |
| Regulated actuator (429850) | Used in larger systems to pressurise additional tanks at the same time. |
| Tank enclosure (429870) | Holds an additional 1.5 or 3.0 gallon tank in double and multiple-tank systems. |
| Nozzles | Eleven nozzle types (1/2N, 1F, 1W, 1N, 2W, 230, 245, 260, 290, 2120, 3N), each designed for a specific appliance, plenum or duct application. They must only be used where the design allows. |
| Blow-off caps (metal / rubber) | Cover the nozzle tip to keep grease out of the orifice. |
| Detectors and fusible links | Up to 15 detectors per detection line (14 series and 1 terminal). The link rating is chosen according to the normal temperature at each location. |
| Remote manual pull station (434618) | Lets staff operate the system by hand. |
| Mechanical gas valve | Closes the gas supply to the appliances when the system operates. Electrical gas valves are also available. |
How a system is sized: flow numbers
Each nozzle has a flow number. The designer adds up the flow numbers of all nozzles needed for the appliances, plenum and duct, and the total decides how many tanks and which cartridge the system needs:
| Total flow numbers | Agent tanks |
|---|---|
| Up to 5 | One 1.5 gallon tank |
| 6 to 11 | One 3.0 gallon tank |
| Up to 16 | One 1.5 gallon + one 3.0 gallon tank |
| Up to 22 | Two 3.0 gallon tanks |
| Larger systems | Several tanks with additional cartridges and regulated actuators (up to 110 flow numbers) |
Because the R-102 is pre-engineered, every pipe length, fitting and nozzle position must stay within the limits of the manual. That is why the design, installation and service must be carried out by technicians trained and certified by ANSUL.
Choosing fusible links
| Link rating | Use where the normal temperature does not exceed |
|---|---|
| 165°F (74°C) | 100°F (38°C) |
| 212°F (100°C) | 150°F (66°C) |
| 280°F (138°C) | 225°F (107°C) |
| 360°F (182°C) | 290°F (143°C) |
| 450°F (232°C) | 360°F (182°C) |
| 500°F (260°C) | 400°F (204°C) |
Maintenance schedule
| When | What the certified technician does |
|---|---|
| Every six months | Full maintenance examination: checks that the system still matches the appliances and hood layout, replaces all fusible links, tests the pull station, gas valve and electrical switches, inspects and aims the nozzles, checks the blow-off caps and weighs the cartridge (it is replaced if it has lost half an ounce, about 14 g, or more). |
| Every year | In addition: blows dry air or nitrogen through the piping to make sure it is not blocked, and replaces all rubber blow-off caps (metal caps do not need annual replacement). |
| Every 12 years | In addition: hydrostatic test of the agent tanks, a fresh charge of agent and a flow test of the regulators. |
| After hood and duct cleaning | The manufacturer strongly recommends a full inspection right after cleaning, because cleaning chemicals or handling can affect the detection equipment. |
Between visits, kitchen managers should keep the pull station visible and unobstructed, make sure the blow-off caps are on the nozzles, and tell us before moving, adding or replacing any cooking appliance, because the nozzles are positioned for the current layout. Parts such as test links, the regulator test kit and the cocking lever with lock pin are used by technicians during these visits.
After the system discharges
- Have the cause of the discharge found and corrected, then have the system recharged immediately by a certified technician. Until then the kitchen is unprotected.
- Clean the agent off kitchen surfaces within 24 hours, because the agent is alkaline.
- Before cleaning: shut off gas and electricity to the appliances and the hood, and let all surfaces cool to room temperature. Never use water on appliances that still contain hot oil.
- Throw away any food and cooking oil that the agent has touched.
- Wear rubber gloves, sponge up the agent, then wash surfaces with hot soapy water, rinse and let them dry completely before switching equipment back on.
A portable extinguisher is still required
The manufacturer requires portable fire extinguishers in the kitchen as part of the total design, including a Class K extinguisher wherever cooking oils and fats are used, for fires in areas the fixed system does not cover.
Frequently asked questions
How often does an ANSUL system need maintenance?
Every six months by an ANSUL-certified technician, with extra annual checks and a 12-year examination that includes hydrostatic testing of the tanks and a fresh charge of agent.
How often are fusible links replaced?
At every semi-annual maintenance visit, all fusible links are removed and replaced with correctly rated ANSUL links, in line with NFPA 17A.
Does the exhaust fan stop when the system discharges?
Not necessarily. The manufacturer recommends leaving exhaust fans running to help move the agent through the duct, while make-up air fans inside the protected hood must shut down.
Is the agent harmful to people?
The manufacturer describes the agent as non-toxic, but it is alkaline and can irritate sensitive skin, so wear rubber gloves during cleanup. Food that it touches must be thrown away.
How long does the agent last?
The ANSULEX Low pH agent has a storage life of twelve years, which is why the tanks are refilled with fresh agent at the 12-year examination.
Do you service systems installed by other companies?
Yes. We inspect existing ANSUL R-102 systems, recharge them after discharge and replace parts with genuine ANSUL parts.
Book an inspection or a quote
Call or WhatsApp us on 0571535353, email info@amh-co.com or use our contact page. We serve Makkah, Jeddah, Riyadh and all cities in Saudi Arabia.